Cold climate

Bathroom exhaust fan requirements in Minnesota

Key takeaways

  • Minnesota’s residential code (Section R303.3) requires a bathroom to have either windows with at least 3 sq ft of glass, half of it openable, or artificial light plus an exhaust system that sends the air directly outdoors.
  • The U.S. Department of Energy’s Building America guide cites the model code’s minimum: 50 cfm for a fan you switch on or 20 cfm for one that runs continuously. The Home Ventilating Institute sizes bathrooms up to 100 sq ft at 1 cfm per square foot, never below 50 cfm.
  • Minnesota’s energy code calls for R-8 insulation with a vapor retarder on ducts in attics, garages and ventilated crawl spaces, a key defense against a fan duct that drips in January.
  • Blaine and Maple Grove put bathroom fans under a mechanical permit. In St. Paul, 57% of bathroom-remodel permits that list trade permits list a ventilation trade permit (city data from 2023, ending June 30, 2025).
  • The Minnesota Department of Health advises keeping indoor humidity at 20–40% in winter and using bathroom fans that are ducted to the exterior.

Next step

Find out which bathroom work needs which permit in Minneapolis, St. Paul and 13 suburbs, and who issues it.

Minnesota’s bathroom exhaust fan requirements start with a choice: a bathroom needs either windows with at least 3 square feet of glass, half of it openable, or artificial light plus an exhaust system that sends the air directly outdoors. That rule is Section R303.3 of the Minnesota Residential Code, the 2018 International Residential Code (IRC) as the state adopted it. The minimum fan size in national guidance is 50 cubic feet per minute (cfm) for a fan you switch on, or 20 cfm for one that runs continuously, according to the U.S. Department of Energy’s Building America guide, which cites the model code and ASHRAE 62.2. The window is legal, but the Minnesota Department of Health’s mold guidance is simpler: install and use bathroom exhaust fans that are ducted to the exterior.

The code minimum is the easy part. In a Twin Cities winter, watch the duct: warm, wet shower air that meets a cold, uninsulated duct condenses and can drip back through the fan or soak the insulation around it.

Bathroom ventilation code in Minnesota: the rules at a glance

Requirement What the rule says Where it comes from
Window or fan 3 sq ft of glass, half openable, or artificial light plus local exhaust Minnesota Residential Code R303.3
Where the air goes “Exhausted directly to the outdoors” R303.3 exception
Fan capacity 50 cfm intermittent or 20 cfm continuous DOE Building America guide, citing the IRC and ASHRAE 62.2 (R303.3 points to Section M1505 for the rate)
Duct in an attic, garage or ventilated crawl space R-8 insulation with a vapor retarder Minn. R. 1322.0403, Table R403.2.1
Exhaust duct inside the house R-3.3 with a vapor retarder, within 3 ft of the exterior or an unconditioned space Minn. R. 1322.0403, Table R403.2.1
Exterior outlet location DOE recommends at least 10 ft from a mechanical air inlet or 3 ft from a gravity air inlet. Confirm clearance for the planned outlet with the local inspector. DOE Building America installation guidance

Source: Minnesota Residential Code 2020 (UpCodes); Minn. R. 1322.0403; Pacific Northwest National Laboratory, Building America Solution Center (accessed October 2026).

Which code sets the number?

Minnesota adopted the 2018 IRC but replaced its mechanical chapters with the state’s own mechanical code (Minn. R. 1309.0010), and it sends ventilation in houses built under the IRC to the state energy code, chapter 1322 (Minn. R. 1346.0401; the amended R303.4 in Minn. R. 1309.0303 points to chapter 1322 or 1346). Section R403.5 exempts standalone bath fans from its whole-house ventilation requirements. Section R403.5.1 also exempts alterations to existing buildings from R403.5. The duct-insulation requirements are in a separate section, R403.2.1.

So the window-or-fan rule lives in the residential code, and 50 cfm is the model-code minimum that the U.S. Department of Energy and the Home Ventilating Institute (HVI) use. Maple Grove’s basement-finishing handout ties the fan’s minimum rating to the 2020 Minnesota Mechanical and Fuel Gas Code. Ask your city’s inspector which rating they check before you buy a fan.

Bathroom fan cfm: how big a fan you need

HVI’s sizing rule for bathrooms up to 100 square feet is 1 cfm per square foot of floor area, with a minimum of 50 cfm. For larger bathrooms, add up the fixtures instead.

Bathroom HVI method Minimum fan
5 × 8 ft hall bath (40 sq ft) 1 cfm per sq ft, but not below 50 50 cfm
8 × 10 ft bath (80 sq ft) 1 cfm per sq ft 80 cfm
10 × 10 ft bath (100 sq ft) 1 cfm per sq ft 100 cfm
120 sq ft primary bath with toilet, shower and tub 50 + 50 + 50 cfm 150 cfm
Same bath with a jetted tub instead of a standard tub 50 + 50 + 100 cfm 200 cfm
Enclosed toilet room HVI says it should have its own fan Sized separately

Source: Home Ventilating Institute, “How Much Ventilation Do I Need?” and “Bathroom Ventilation” (see Sources). Examples are our calculations using HVI’s rules.

HVI also allows continuous ventilation at a minimum of 20 cfm in place of an intermittent 50 cfm fan. That matches the code’s continuous option.

A fan’s rated cfm is not what it delivers through a long, crooked duct. Maple Grove’s handout notes that rigid metal duct “creates much less resistance to air flow” and will improve the fan’s efficiency. The Building America guide says smooth rigid duct is preferred over flex, any aluminum flex should be stretched tight, and the duct diameter should match what the fan maker specifies. If an older fan is being replaced and the existing duct is undersized or crushed, budget for a new duct run, not just a new fan.

Bathroom fan vent: through the roof, wall or soffit, never the attic

The Building America guide is blunt: “Install the fan to vent outdoors, not into an attic, crawlspace, or space between floors.” It also lists garages and wall cavities as unacceptable. For a fan that takes the place of a window, Minnesota’s code says the same thing in fewer words: exhaust “directly to the outdoors.”

That leaves three common exits:

  • Through the roof. A roof cap above the fan. The guide’s diagrams show both wall and roof exits as acceptable. The risk is a long vertical run through a cold attic.
  • Through a side wall. Often the shortest run when the bathroom sits on an exterior wall. The guide suggests placing the wall terminal slightly below the fan so the duct can drain outward.
  • Through the soffit. The duct has to run all the way to its own exterior fitting. A duct that stops short of the soffit leaves the air in the attic, which isn’t “directly to the outdoors.” The guide’s own training example says exhausting to the soffit vent would be preferable to an overly long roof run.

For a wall exit, the guide says the cap should include a damper that closes when the fan is off.

Watch out: In older houses it’s worth checking where an existing fan actually goes. A duct that ends loose in the attic, or a fan with no duct at all, doesn’t meet the “directly to the outdoors” rule and puts shower moisture straight into the attic insulation.

Stopping winter condensation in the fan duct

Moist air cooled below its dew point turns to water. In an attic in a Minnesota winter, an uninsulated bath duct can collect enough of it to drip from the fan grille. Three details help prevent it:

  1. Insulate the duct. Minnesota’s energy code calls for R-8 insulation with a vapor retarder on ducts in attics, garages and ventilated crawl spaces. Exhaust ducts inside the heated part of the house need R-3.3 with a vapor retarder within 3 feet of the exterior or an unconditioned space. Blaine’s bathroom page puts it plainly: exhaust ducts “shall be insulated for a minimum of 3 feet from the exterior wall.”
  2. Slope it toward the outside. For a side-wall exit, the Building America guide says to put the terminal slightly below the fan so the duct can “slope down and away from the housing.” Any condensate then drains out rather than back into the fan.
  3. Keep it short and damped. A short, straight, smooth duct moves more air and has less cold surface. A damper at the exterior cap keeps winter air from pouring back in when the fan is off.

Local note: About 84% of owner-occupied homes in Minneapolis and 86% in St. Paul were built in 1979 or earlier, per the Census Bureau’s 2020–2024 American Community Survey. In an older house, check whether the bathroom sits on an uninsulated exterior wall and whether the fan duct crosses an attic that was re-insulated after the fan went in. Castle Building & Remodeling’s 2026 half-bath remodel scope, for example, includes insulating exterior walls and adding a new bath fan vented to the exterior.

Bathroom mold and winter condensation in Minnesota

The Minnesota Department of Health (MDH) says controlling moisture is the best way to prevent mold. Its guidance for homes:

  • Keep relative humidity between 20 and 40 percent in winter, and below 60 percent the rest of the year.
  • Install and use exhaust fans in bathrooms and kitchens that are ducted to the exterior.
  • Look for signs of excess moisture, including condensation on windows and exterior walls. MDH’s fix is to raise the temperature and air circulation in colder parts of the house.
  • Dry wet materials within 24 to 48 hours to keep mold from growing.

Run time matters as much as fan size. HVI calls for a timer or other control that keeps the fan running at least 20 minutes after each use. The Building America guide recommends one hour after a shower and suggests a timer switch instead of a standard wall switch, so the fan shuts itself off. HVI lists timers, humidistats, variable-speed controls and fan-light combinations among the control options. A humidistat or humidity-sensing control helps in a household where nobody remembers to leave the fan on.

If you’re adding a heated floor as part of the remodel, it warms the room but doesn’t remove moisture. You still need the fan.

Sones, noise and efficiency

A fan nobody runs because it’s loud does nothing. Fan noise is rated in sones. HVI says one sone is about the sound of “a quiet refrigerator in a quiet kitchen.”

Benchmark Continuous fan Intermittent fan
ENERGY STAR recommendation (per DOE guide) 1 sone or less 3 sones or less
Minnesota energy code, fans used to meet R403.5 whole-house requirements 1.0 sone max (surface-mounted) 2.5 sones max

Source: Pacific Northwest National Laboratory, Building America Solution Center; Minn. R. 1322.0403, R403.5.7 (accessed October 2026).

For a fan replacement in an existing bathroom, use these sound ratings to compare products. Section R403.5.1 exempts alterations to existing buildings, and R403.5 also excludes standalone bath fans. Where R403.5.7 does apply, it has separate provisions for remote fans and forced-air systems. HVI notes that remote fans, mounted outside the building, keep much of the mechanical sound outside. ENERGY STAR says its certified ventilation fans use about 48% less energy than standard models, which matters if the fan will run continuously.

Permits for a bathroom exhaust fan in the Twin Cities

Minnesota requires plumbing, electrical and mechanical permits unless the work is specifically exempt (Minn. R. 1300.0120). How cities handle a bath fan varies:

City Fan and duct Fan wiring (electrical)
Blaine Mechanical permit for “bathroom ventilation fan/duct,” with a rough-in inspection before the duct is covered Issued by the State of Minnesota
Maple Grove Mechanical permit for “bathroom ventilation,” per the basement-finishing handout City issues and inspects
St. Paul 57% of bathroom-remodel permits that list trade permits include a ventilation (“W.Air Vent”) permit (2023 to June 30, 2025; city data ends there) City issues and inspects
Minneapolis State rule applies (mechanical permit unless exempt); owner-occupants of single-family homes may do their own mechanical work State (DLI) issues and inspects

Source: City of Blaine; City of Maple Grove; City of Saint Paul permit data, our analysis of 454 permits through June 30, 2025; City of Minneapolis; Minnesota DLI Local Code Lookup (accessed October 2026).

The State also handles electrical permits in Edina, Eden Prairie and Eagan. Bloomington, Plymouth, Woodbury, Minnetonka, Burnsville, Lakeville, St. Louis Park and Roseville run their own electrical inspections. Our permit guide covers city-by-city details, and the permit data report explains the St. Paul figures.

What it costs to add or replace a bathroom fan

HomeAdvisor’s national bathroom remodel guide (updated June 2026) says bathroom fan installation costs $400 on average. It’s a national figure and doesn’t say what a new duct run through an insulated attic, a roof penetration, a new circuit or a ceiling patch will add.

In the local remodel budgets we checked, the fan is a line inside the larger job. Castle’s 2026 Twin Cities guide lists a new exhaust fan in two of its three 5 × 8 ft hall-bath scenarios ($45,000–$65,000 and $55,000–$70,000); the scope for the third ($65,000–$80,000) doesn’t mention one. Its 18 sq ft half-bath remodel ($36,047–$41,454) includes a new fan vented to the exterior. Its 40 sq ft bathroom makeover ($25,371–$29,177) excludes the fan, so a fan upgrade there would be added scope. When you compare bids, check whether the fan, the duct to the outside, the exterior cap and the mechanical permit are each listed. See the quote checklist and our bathroom remodel costs and calculator.

Next steps

  1. Measure the room and size the fan with HVI’s rule: 1 cfm per square foot up to and including 100 sq ft (50 cfm minimum), or 50 cfm per fixture above that (100 for a jetted tub).
  2. Find out where your current fan goes. If the duct ends in the attic or isn’t insulated, fix that before the ceiling closes.
  3. Plan the exit (roof, wall or soffit) with the shortest, straightest duct possible, sloped toward the outside, with a damped cap.
  4. Choose the control: a timer or humidity-sensing switch that keeps the fan on 20 to 60 minutes after a shower.
  5. Call your city to confirm whether the fan needs a mechanical permit and who issues the electrical permit.

Keep planning

Find out which bathroom work needs which permit in Minneapolis, St. Paul and 13 suburbs, and who issues it.

Frequently asked questions

Is a bathroom exhaust fan required in Minnesota?

Only if the bathroom lacks a qualifying window. Minnesota’s residential code accepts windows with at least 3 sq ft of glass, half of it openable; without them you need artificial light and an exhaust system vented directly outdoors.

What size bathroom fan do I need?

The Home Ventilating Institute uses 1 cfm per square foot for bathrooms up to 100 sq ft, with a 50 cfm minimum. For larger baths, add 50 cfm each for the toilet, shower and tub, and 100 cfm for a jetted tub.

Can a bathroom fan vent into the attic or out the soffit?

Not into the attic. Minnesota’s residential code says a fan used in place of a window must exhaust directly to the outdoors, and the Department of Energy’s Building America guide rules out attics, crawlspaces and spaces between floors. A roof, wall or soffit exit can work if the duct runs all the way to its own exterior cap.

Do I need a permit to add or replace a bathroom fan in Minnesota?

Often. Minnesota requires mechanical permits unless the work is specifically exempt, and Blaine and Maple Grove both list bathroom ventilation under a mechanical permit. New wiring also needs an electrical permit, issued by the State in cities such as Minneapolis and Blaine.

Why does my bathroom fan drip water in the winter?

Warm, wet air condenses when it hits a cold, uninsulated duct, and the water runs back to the fan. Minnesota’s energy code calls for R-8 insulation with a vapor retarder on ducts in attics. For a side-wall exit, the Building America guide says to slope the duct down and away from the fan.

How long should a bathroom fan run after a shower?

The Home Ventilating Institute calls for controls that keep the fan running at least 20 minutes after each use. The Department of Energy’s Building America guide recommends one hour after a shower, set with a timer switch.

Sources

  1. Bathroom Ventilation, room-size and fixture sizing guidelines (opens in a new tab) — Home Ventilating Institute. Accessed .
  2. Minnesota Residential Code 2020, Chapter 3, Section R303 (Light, Ventilation and Heating) (opens in a new tab) — UpCodes (Minnesota Residential Code text). Accessed . R303.3 Bathrooms and exception; R303.4 Mechanical ventilation as amended by Minnesota.
  3. Minn. R. 1309.0010, Adoption of International Residential Code by reference (opens in a new tab) — Minnesota Office of the Revisor of Statutes. Accessed . Adopts the 2018 IRC; IRC chapters 12 to 24 (mechanical) replaced by Minnesota Rules chapter 1346, chapter 11 by chapters 1322 and 1323.
  4. Minn. R. 1309.0303, Section R303, Light, Ventilation, and Heating (opens in a new tab) — Minnesota Office of the Revisor of Statutes. Accessed .
  5. Minn. R. 1346.0401, Section 401 General (ventilation) (opens in a new tab) — Minnesota Office of the Revisor of Statutes. Accessed .
  6. Minn. R. 1322.0403, Section R403, Systems (duct insulation, mechanical ventilation) (opens in a new tab) — Minnesota Office of the Revisor of Statutes. Accessed . Table R403.2.1 duct insulation; R403.5 exception for standalone fans, R403.5.1 exemption for alterations to existing buildings, and R403.5.7 fan sound limits and exceptions.
  7. Bathroom Exhaust Fans (Building America Solution Center) (opens in a new tab) — Pacific Northwest National Laboratory for the U.S. Department of Energy. Accessed . Last updated Dec. 4, 2022. Cites ASHRAE 62.2 and the 2021 IRC for the 50 cfm intermittent / 20 cfm continuous rates.
  8. How Much Ventilation Do I Need? (opens in a new tab) — Home Ventilating Institute (HVI). Accessed .
  9. HVI-Certified Ventilation Performance (opens in a new tab) — Home Ventilating Institute (HVI). Accessed .
  10. Types of Fans (opens in a new tab) — Home Ventilating Institute (HVI). Accessed .
  11. Ventilation Fans (opens in a new tab) — ENERGY STAR (U.S. EPA). Accessed .
  12. Mold in Homes (opens in a new tab) — Minnesota Department of Health. Accessed .
  13. Bathroom Project (opens in a new tab) — City of Blaine. Accessed .
  14. Basement Finishing (handout, Rev. 4/6/2021) (opens in a new tab) — City of Maple Grove Building Department. Accessed .
  15. Approved Building Permits, PermitPriced analysis (data ends June 30, 2025) (opens in a new tab) — City of Saint Paul. Accessed . Of 454 bathroom-remodel permits listing required trade permits, 259 list W.Air Vent (ventilation).
  16. Minnesota Rules 1300.0120, Permits (opens in a new tab) — Minnesota Office of the Revisor of Statutes. Accessed .
  17. Plumbing permits (opens in a new tab) — City of Minneapolis. Accessed .
  18. Local Code Lookup (electrical inspection authority by city) (opens in a new tab) — Minnesota Department of Labor and Industry. Accessed .
  19. How Much Does It Cost to Remodel a Bathroom? (opens in a new tab) — HomeAdvisor. Accessed . National figures; updated June 17, 2026.
  20. 2026 Twin Cities Remodeling Cost Guide (pp. 14–15) (opens in a new tab) — Castle Building & Remodeling. Accessed . Design-build firm; prices assume pre-1960 homes and average finishes.
  21. Table B25036, Tenure by Year Structure Built (ACS 2020–2024 5-year), Minneapolis and St. Paul (opens in a new tab) — Census Reporter (U.S. Census Bureau data). Accessed .

Our guides are written independently, and we don’t rank remodelers. How we research.

Free tool

Bathroom remodel cost calculator

Get a range for a full remodel or a shower or tub replacement with tiled walls. Other projects, such as replacing an acrylic or panel system on its own, get a checklist.